> Windows 98
> Windows 98 Startup Problems
Windows 98 Startup Problems
Not all of the icons that start up will show up on your system tray. Then came the flood of follow-up inputs, and the thread grew exponentially and my understanding shrank concomitantly. You can always consult Microsoft’s Support Web site for more details specific to your GPF error. Kansas is going bye bye.Once you are ready to delete all yoor files, enter the PC by DOS mode, (push F8 at the startup to be able to use the operating Source
Once all of the new device drivers have been loaded, you may have to manually reconfigure some settings such as your network connection. OR B: you have a floppy in the drive BUT you don't (IMO) have a proper boot disk. Caveat: Not every CD-ROM drive is supported by the drivers included on the Windows 98 Startup disk/EBD. MoondogJuly 5th, 2015, 10:12 PMIt's good to hear it worked. https://forums.techguy.org/threads/windows98-new-on-hard-drive-bootup-troubles.84117/
Windows 98 Startup Problems
Flag Permalink This was helpful (0) Collapse - Downloading SP2 to CD by tday / March 12, 2005 3:49 AM PST In reply to: Slipstreaming service pack 2 to a new And there may be other problems occurring that I'm not aware of. I can not get the cd-rom to work now it said no driver or drivers found. Then install DirectX & then proceed to graphics drive & then go to others.It is always advisable to install security updates before going online.Hope that helpsSubmitted by: Aditya R.
- if not you could download the drivers from the manufactor website ...
- Job done and without the use of any third party partitioning programs.
- Newer » This thread is closed to new comments.
- Yes you should.
- I've run on the same harddrive image, without ever reformatting, for a decade!
- If that happens to be your collection of MP3 or WMA CD rips, it's going to be very quiet at your home or office until you get that hard disk back
- Delete partition or logical DOS Drive. 4.
- Note: Make sure your CD?s are clean of any finger prints and smudges by wiping them from the center out.
Caluser2000June 5th, 2015, 03:46 PMYou've answered your post then. Doing so tends to prevent device conflicts. That right there tells me it isn't, unless like has already been mentioned that you manually set the geometry and prep the drive on that machine. Windows 98 Startup Disk if you have access to a PCI IDE controller you can borrow, try that before buying - i had a similar situation (system wouldn't recognize anything on primary IDE) that couldn't
Follow the onscreen instructions for installing XP. I have been in the process of backing up all of my data as well as getting rid of extraneous data. You can use Norton's ghost or pay out $50.00 US. This antivirus program will not only run in Safe Mode, but it can also repair many of the most destructive viruses.
cd windows\commandsmartdrv.exebootdisk a:d. Caluser2000June 5th, 2015, 02:54 PMWe need more detail about your setup. Trying to format the hard drive so I can install windows 98. I have made many images of Windows 98 and restored them successfully to new hard drives.
Windows 98 Stuck On Loading Screen
Table 3.2 179 I'm not sure how to jumper my ATA/IDE drives. https://www.cnet.com/forums/discussions/windows-98-will-not-boot-up-even-with-bootdisk-106332/ Please try again now or at a later time. Windows 98 Startup Problems A bootable XP disk will repair, delete, reformat, and or install itself depending on what you want, just by inserting the disk and booting the machine to the disk when prompted Windows 98 Won't Boot And I had to call Microshaft any way.
It is to long a story why I pick NTFS but it will format your drive and install XP the way you want. this contact form Before you get gloomy and decide that today's the day that your hard disk has really failed, cheer up! Flag Permalink This was helpful (0) Collapse - Saying Goodbye to XP for Linux by jeffrob / February 24, 2005 9:11 PM PST In reply to: Getting rid of XP I'd I won't repeat the many excellent ways to back up and the other tips. Repair Windows 98
The system will just boot the card's BIOS, and it will handle the rest. Intel just thought the hardware would be outdated by the time a drive that big would be on the market. by TONI H / May 29, 2005 10:04 PM PDT In reply to: Unable to get the computer up and running in Safe Mode EXPLORER.EXE ERROR AND CAN'T GET TO THE have a peek here ATA/IDE Disk Drive Installation Troubleshooting 679 I can't use any drive connected to the ATA/IDE interface in my computer.
I'd also add that you likely just need to replace the original FDISK with the updated FDISK that handles larger hard drives. Eventually, you should see a boot menu, and Safe Mode will be one of the choices.When Windows boots into Safe Mode, it’s running at minimal capacity. Do you have the time to do it, or should you wait until later?Alright, now for what you asked for:1) Make sure you have everything that you need off of your
You can download one at bootdisk.com.
Every programs I've tried had no problems imaging the Aptiva's hard drive and had no problems writing the Aptiva's hard drive image to the Quantum hard drive. Copy the Wpa.dbl file from the floppy disk to the C:\Windows\System32 folder.8. Click here to join today! It works perfectly.
For what it's worth, here is where my situation lies: This a Compaq Presario desktop (5WV260). Please refer to our CNET Forums policies for details. If the hard disk that starts your computer isn't working correctly, you'll see an error message referring to a missing "boot device." Although the computer industry likes to use the term http://winnthosting.com/windows-98/windows-98-download.html The suggestions so far seem logical, thanks.
Early revisions of the chipset exhibited this hard lock behavior with large drives and it wasn't fixable with the BIOS- this is the problem I'm familiar with. (I work for a Keep in mind that the word "program" doesn’t necessarily refer to an application, such as Microsoft Word. Install new drive into the target device. 6. Your CPU might be the fastest on your block and your memory might be smokin' fast, but if your hard disk decides not to wake up in the morning, your computer's
If not they will need to repurchase a new Key Code or request a replacement from Microsoft. If the screen comes on but the system never displays any activity from the hard disk, your system (boot) hard disk isn't working. This will uninstall the driver that’s associated with each device. Flag Permalink This was helpful (0) Collapse - how do i open my pc?
Port can't provide power to drive. Buffer Underrun Problems 685 I can't copy (drag and drop) files to a CD-R or CD-RW disc. Year: 1994. In the Fdisk mode (if you get there) you want to select DELETE prinary dos function first. (3) Then after the machine checks the integraty of the hard drive it will
Thread Status: Not open for further replies. Then relaod the drivers you downloaded, transfer the saved data files and you are done.Submitted by: Stuart*************************************************************************** Answer: First i would check to see if your computer came with a system When I tried to burn it to a CD I get a message that a file attached to it might be lost, continue? Follow onscreen instructions. (takes about 30 min) Follow Steps 5 thru 15 above C.
Formatting is not necessary for optical media that will be used with a CD mastering program such as Easy CD Creator or Nero Burning ROM. I would think that, if you partition the drive into 32GB/32GB/16GB chunks and format each as FAT32, the drive should be recognizable by Win98, albeit divided.